Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Classifieds
Media
New media
New comments
Search media
Log in
Register
What's New?
Search
Search
Search titles only
By:
New posts
Search forums
Menu
Log in
Register
Navigation
Install the app
Install
More Options
Advertise with us
Contact Us
Close Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Forums
The Range
Handgun Discussion
AR-9 pistol build
Search titles only
By:
Reply to Thread
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Message
<blockquote data-quote="Tanis143" data-source="post: 3345070" data-attributes="member: 43724"><p>Btw, for those looking for a good upper vise block I can now recommend the Vism brand one. Tested it out and the upper I attached to it did not wiggle or budge one bit. Here is a link to it on Amazon:</p><p></p><p><a href="https://www.amazon.com/ATG-Patch-NcSTAR-Heavy-Modular/dp/B07R6JVHM4/ref=sr_1_1?crid=2WIL7UYP4B2K2&dchild=1&keywords=vism+upper+receiver+vise+block&qid=1585686151&s=sporting-goods&sprefix=vism+upp%2Csporting%2C169&sr=1-1" target="_blank">https://www.amazon.com/ATG-Patch-NcSTAR-Heavy-Modular/dp/B07R6JVHM4/ref=sr_1_1?crid=2WIL7UYP4B2K2&dchild=1&keywords=vism+upper+receiver+vise+block&qid=1585686151&s=sporting-goods&sprefix=vism+upp,sporting,169&sr=1-1</a></p><p></p><p>The bcg section is held on by two hex bolts. Once removed you slide it into the upper, then place the combo onto the bottom section. You put in the two pins were the take down eyelets are and then bolt the two pieces of the block back together. Afterwards the upper is held completely still and the pressure is spread out over the whole upper. You can also just use the bottom piece by itself if you are just doing maintenance with no torquing. This will work for AR15, AR10, AR9, etc.</p></blockquote><p></p>
[QUOTE="Tanis143, post: 3345070, member: 43724"] Btw, for those looking for a good upper vise block I can now recommend the Vism brand one. Tested it out and the upper I attached to it did not wiggle or budge one bit. Here is a link to it on Amazon: [URL]https://www.amazon.com/ATG-Patch-NcSTAR-Heavy-Modular/dp/B07R6JVHM4/ref=sr_1_1?crid=2WIL7UYP4B2K2&dchild=1&keywords=vism+upper+receiver+vise+block&qid=1585686151&s=sporting-goods&sprefix=vism+upp%2Csporting%2C169&sr=1-1[/URL] The bcg section is held on by two hex bolts. Once removed you slide it into the upper, then place the combo onto the bottom section. You put in the two pins were the take down eyelets are and then bolt the two pieces of the block back together. Afterwards the upper is held completely still and the pressure is spread out over the whole upper. You can also just use the bottom piece by itself if you are just doing maintenance with no torquing. This will work for AR15, AR10, AR9, etc. [/QUOTE]
Insert Quotes…
Verification
Post Reply
Forums
The Range
Handgun Discussion
AR-9 pistol build
Search titles only
By:
Top
Bottom