Reply to Thread

Message

<blockquote data-quote="Ians 17/22" data-source="post: 3987697" data-attributes="member: 51816">HA HA HA ....That bad Huh??.....with-in my shop / factory the Best equipment wasn&#039;t good enough , never stoped looking for better / up-grading.....if those 2 Hardinges run &amp; the re-ostate that controls the feed on the Chucker works or even if new brushes were needed for it to run (very simple to install) , can&#039;t imagine they have been posted for 8 days &amp; not sold !!!!!!.......i&#039;d bet 2000 bucks would get them both.....that would be a steal even 20yrs ago....the chucker is known for holding tolerences in the tenths of thousands , that&#039;s the accuracy of the chucker.....i used to make dentist tools on that hand screw , useing 1095 Dr.rod 1/8 diameter &amp; turning a diameter to .006 x 3/4 &quot; long , O.V.L. was 2&quot;s....not to mention the hundreds of other close tolerance parts , when i retired &amp; had to sell all (made me sick)i had 2 toolroom lathes , 2 hand screws , 3 C.N.C. all hardinge &amp; 2 Chuckers , 2 Bridgports , 3 # 3 W&amp;S turretts , 5 B &amp; S Auto screw machines , punch Presses to 35 ton , surface , tool &amp; cutter ,&amp; center grinders..... plus complete Gov&#039;t certified inspection dept.....am listed in H57 as approved fastener Mfg&#039;er......also mfg&#039;ed medical items , 1 of which was written up in a med journal , was a Torque &quot;special driver&quot; used to put pins in the head of patients......&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; AAAHHH i&#039;m simply reminishing , sure do miss the days.....&nbsp; &nbsp; &nbsp; &nbsp;&nbsp; If someone here buys those machines , i will sure help if needed.....Thanks 4 listening to this ol guy.....HA HA</blockquote>

[QUOTE="Ians 17/22, post: 3987697, member: 51816"] HA HA HA ....That bad Huh??.....with-in my shop / factory the Best equipment wasn't good enough , never stoped looking for better / up-grading.....if those 2 Hardinges run & the re-ostate that controls the feed on the Chucker works or even if new brushes were needed for it to run (very simple to install) , can't imagine they have been posted for 8 days & not sold !!!!!!.......i'd bet 2000 bucks would get them both.....that would be a steal even 20yrs ago....the chucker is known for holding tolerences in the tenths of thousands , that's the accuracy of the chucker.....i used to make dentist tools on that hand screw , useing 1095 Dr.rod 1/8 diameter & turning a diameter to .006 x 3/4 " long , O.V.L. was 2"s....not to mention the hundreds of other close tolerance parts , when i retired & had to sell all (made me sick)i had 2 toolroom lathes , 2 hand screws , 3 C.N.C. all hardinge & 2 Chuckers , 2 Bridgports , 3 # 3 W&S turretts , 5 B & S Auto screw machines , punch Presses to 35 ton , surface , tool & cutter ,& center grinders..... plus complete Gov't certified inspection dept.....am listed in H57 as approved fastener Mfg'er......also mfg'ed medical items , 1 of which was written up in a med journal , was a Torque "special driver" used to put pins in the head of patients...... AAAHHH i'm simply reminishing , sure do miss the days..... If someone here buys those machines , i will sure help if needed.....Thanks 4 listening to this ol guy.....HA HA [/QUOTE]

Verification